Forskjell mellom versjoner av «Stag Beetle 3D printer»
Hopp til navigering
Hopp til søk
(→Historikk: OctoPi 0.18.0 and OctoPrint 1.8.6 is in) |
(→Om printeren: add print volume description) |
||
(5 mellomliggende revisjoner av samme bruker vises ikke) | |||
Linje 9: | Linje 9: | ||
* nozzle: 0.4 mm | * nozzle: 0.4 mm | ||
* Hostnavn: <code>stagbeetle.local</code> | * Hostnavn: <code>stagbeetle.local</code> | ||
+ | * build plate printable area: 250 x 210 mm | ||
+ | * max printable height: 210 mm | ||
== Firmware == | == Firmware == | ||
− | Firmware version: 3. | + | Firmware version: 3.11.0-4955 |
== OctoPrint == | == OctoPrint == | ||
− | * OctoPrint: 1. | + | * OctoPrint: 1.8.6 |
− | * OctoPi: 0. | + | * OctoPi: 0.18.0 |
== Historikk == | == Historikk == | ||
+ | ; 2022-12-27 : upgraded firware to version 3.11.0-4955 via OctoPrint. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 27. des. 2022 kl. 21:36 (CET) | ||
+ | ; 2022-12-27 : installed avrdude for firmware flashing, via <code>sudo apt install avrdude</code>. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 27. des. 2022 kl. 21:31 (CET) | ||
+ | |||
; 2022-12-27 : OctoPrint - wrote OctoPi 0.18.0 / OctoPrint 1.8.6 to a re-used microSD card and installed in the printer. Configuration: <code>/boot/cmdline.txt</code> - removed serial console. After: | ; 2022-12-27 : OctoPrint - wrote OctoPi 0.18.0 / OctoPrint 1.8.6 to a re-used microSD card and installed in the printer. Configuration: <code>/boot/cmdline.txt</code> - removed serial console. After: | ||
<pre> | <pre> | ||
Linje 30: | Linje 35: | ||
</pre> | </pre> | ||
the lines <code>start_x=1</code> and <code>gpu_mem=128</code> were already there. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 27. des. 2022 kl. 19:00 (CET) | the lines <code>start_x=1</code> and <code>gpu_mem=128</code> were already there. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 27. des. 2022 kl. 19:00 (CET) | ||
+ | : restored OctoPrint configuration from a backup. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 27. des. 2022 kl. 19:23 (CET) | ||
; 2022-12-22: OctoPrint - did a backup. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 19:29 (CET) | ; 2022-12-22: OctoPrint - did a backup. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 19:29 (CET) |
Nåværende revisjon fra 13. jul. 2023 kl. 18:34
Stag Beetle er en Original Prusa i3 MK3S[1], kjøpt som byggesett fra Prusa Research[2].
Undersider: bygging,
Bruk: se siden 3D printing.
Om printeren
Her skal det stå litt om printeren.
- nozzle: 0.4 mm
- Hostnavn:
stagbeetle.local
- build plate printable area: 250 x 210 mm
- max printable height: 210 mm
Firmware
Firmware version: 3.11.0-4955
OctoPrint
- OctoPrint: 1.8.6
- OctoPi: 0.18.0
Historikk
- 2022-12-27
- upgraded firware to version 3.11.0-4955 via OctoPrint. Tingo (diskusjon) 27. des. 2022 kl. 21:36 (CET)
- 2022-12-27
- installed avrdude for firmware flashing, via
sudo apt install avrdude
. Tingo (diskusjon) 27. des. 2022 kl. 21:31 (CET)
- 2022-12-27
- OctoPrint - wrote OctoPi 0.18.0 / OctoPrint 1.8.6 to a re-used microSD card and installed in the printer. Configuration:
/boot/cmdline.txt
- removed serial console. After:
pi@stagbeetle:~ $ more /boot/cmdline.txt console=tty1 root=PARTUUID=201b74fb-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
/boot/config.txt
- added these lines to the '[all]' section
dtoverlay=pi3-miniuart-bt force_turbo=1 over_voltage=8
the lines start_x=1
and gpu_mem=128
were already there. Tingo (diskusjon) 27. des. 2022 kl. 19:00 (CET)
- 2021-12-21
- upgraded OctoPrint 1.6.1 to 1.7.2 from OctoPrint UI. Tingo (diskusjon) 21. des. 2021 kl. 19:41 (CET)
- 2021-11-18
- Smørte glidestengene på x og y-aksen fordi ekstruder-vognen gikk så trengt at printeren feilet.
- 2021-06-30
- opprettet bruker "bitraf" i OctoPrint, med standard passord og rolle operatør ("operator"). Tingo (diskusjon) 30. jun. 2021 kl. 15:08 (CEST)
- flashed firmware to 3.10.0-4481 from OctoPrint (Firmware Updater). Tingo (diskusjon) 30. jun. 2021 kl. 17:07 (CEST)
- 2020-08-19
- checked firmware - the printer already has 3.9.0-3421.
- 2019-11-23
- denne siden ble opprettet.