Iron Hive 3D printer: Forskjell mellom sideversjoner

Fra Bitraf
Hopp til navigering Hopp til søk
→Historikk: opprettet bruker "bitraf" i OctoPrint
→Om printeren: this printer has a 0.4 mm nozzle, according to the 3D-printing status page
 
(19 mellomliggende sideversjoner av samme bruker vises ikke)
Linje 7: Linje 7:
== Om printeren ==
== Om printeren ==
Her skal det stå litt om printeren.
Her skal det stå litt om printeren.
* nozzle: 0.4 mm
* Hostnavn: <code>ironhive.local</code>
* Hostnavn: <code>ironhive.local</code>
* build plate printable area: 250 x 210 mm
* max printable height: 210 mm


== Firmware ==
== Firmware ==
Firmware version: 3.10.0-4481
Firmware version: 3.11.0-4955
 
== OctoPrint ==
* OctoPrint: 1.8.6
* OctoPi: 0.18.0


== Historikk ==
== Historikk ==
=== 2023 ===
; 2023-01-22 : camera - replaced it with a new one, now it works.
<pre>
pi@ironhive:~ $ date;vcgencmd get_camera
Sun 22 Jan 15:29:41 CET 2023
supported=1 detected=1
</pre>
That is all for now. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. jan. 2023 kl. 15:30 (CET)
; 2023-01-19 : camera - tested the camera on another printer, it doesn't work there either. And tested the camera from the other printer on this printer, and it works. Conclusion: the camera is defective. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 19. jan. 2023 kl. 19:39 (CET)
=== 2022 ===
; 2022-12-28 : installed avrdude (via <code>sudo apt install avrdude</code>) to facilitate firmware upgrades. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 28. des. 2022 kl. 14:33 (CET)
; 2022-12-23 : Pi camera - the vcgencmd says
<pre>
pi@ironhive:~ $ vcgencmd get_camera
supported=1 detected=0
</pre>
in other words, no camera is detected. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 23. des. 2022 kl. 17:59 (CET)
; 2022-12-22 : test print. Printing via OctoPrint works as before. The Pi camera still doesn't work, must look into that. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 22:37 (CET)
; 2022-12-22 : installed OctoPi 0.18 on a new microSD card by using rpi-imager as described here<ref>[https://octoprint.org/download/ OctoPrint - download]</ref>. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 20:32 (CET)
: result is OctoPi 0.18.0, OctoPrint 1.8.6. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 20:39 (CET)
: added the following lines to <code>/boot/config.txt</code> section '[all]' (the others was already there)
<pre>
dtoverlay=pi3-miniuart-bt
force_turbo=1
over_voltage=8
</pre>
: hopefully this will enable the raspicam stream. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 20:44 (CET)
: I used <code>raspi-config</code> to disable getty on the serial port; <code>sudo raspi-config</code>, then Interface options, Serial Port, "login shell on serial port" = NO, "serial port hardware enabled" = YES. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 21:35 (CET)
; 2022-12-22 : OctoPrint - did a backup. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 22. des. 2022 kl. 20:29 (CET)
; 2022-08-16 : the camera on Ironhive doesn't work (and has been non-working for a while now, according to sources). Unplugging and re-plugging the cable hasn't helped. Perhaps the camera or the cable is broken. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 16. aug. 2022 kl. 16:42 (CEST)
; 2022-04-18 : flashed firmware to 3.11.0-4955 from OctoPrint (Firmware Updater, serial port is <code>/dev/ttyACM0</code>). [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 18. apr. 2022 kl. 16:07 (CEST)
; 2021-06-30 : flashed firmware to 3.10.0-4481 from OctoPrint (Firmware Updater). [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 30. jun. 2021 kl. 17:36 (CEST)
; 2021-06-30 : flashed firmware to 3.10.0-4481 from OctoPrint (Firmware Updater). [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 30. jun. 2021 kl. 17:36 (CEST)
: opprettet bruker "bitraf" i OctoPrint, med standard passord og rolle operatør ("operator"). [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 30. jun. 2021 kl. 17:38 (CEST)
: opprettet bruker "bitraf" i OctoPrint, med standard passord og rolle operatør ("operator"). [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 30. jun. 2021 kl. 17:38 (CEST)

Siste sideversjon per 13. jul. 2023 kl. 16:41

Iron Hive er en Original Prusa i3 MK3S[1], kjøpt som byggesett fra Prusa Research[2].

Undersider: bygging,

Bruk: se siden 3D printing.

Om printeren

Her skal det stå litt om printeren.

  • nozzle: 0.4 mm
  • Hostnavn: ironhive.local
  • build plate printable area: 250 x 210 mm
  • max printable height: 210 mm

Firmware

Firmware version: 3.11.0-4955

OctoPrint

  • OctoPrint: 1.8.6
  • OctoPi: 0.18.0

Historikk

2023

2023-01-22
camera - replaced it with a new one, now it works.
pi@ironhive:~ $ date;vcgencmd get_camera
Sun 22 Jan 15:29:41 CET 2023
supported=1 detected=1

That is all for now. Tingo (diskusjon) 22. jan. 2023 kl. 15:30 (CET)

2023-01-19
camera - tested the camera on another printer, it doesn't work there either. And tested the camera from the other printer on this printer, and it works. Conclusion: the camera is defective. Tingo (diskusjon) 19. jan. 2023 kl. 19:39 (CET)

2022

2022-12-28
installed avrdude (via sudo apt install avrdude) to facilitate firmware upgrades. Tingo (diskusjon) 28. des. 2022 kl. 14:33 (CET)
2022-12-23
Pi camera - the vcgencmd says
pi@ironhive:~ $ vcgencmd get_camera
supported=1 detected=0

in other words, no camera is detected. Tingo (diskusjon) 23. des. 2022 kl. 17:59 (CET)

2022-12-22
test print. Printing via OctoPrint works as before. The Pi camera still doesn't work, must look into that. Tingo (diskusjon) 22. des. 2022 kl. 22:37 (CET)
2022-12-22
installed OctoPi 0.18 on a new microSD card by using rpi-imager as described here[3]. Tingo (diskusjon) 22. des. 2022 kl. 20:32 (CET)
result is OctoPi 0.18.0, OctoPrint 1.8.6. Tingo (diskusjon) 22. des. 2022 kl. 20:39 (CET)
added the following lines to /boot/config.txt section '[all]' (the others was already there)
dtoverlay=pi3-miniuart-bt
force_turbo=1
over_voltage=8
hopefully this will enable the raspicam stream. Tingo (diskusjon) 22. des. 2022 kl. 20:44 (CET)
I used raspi-config to disable getty on the serial port; sudo raspi-config, then Interface options, Serial Port, "login shell on serial port" = NO, "serial port hardware enabled" = YES. Tingo (diskusjon) 22. des. 2022 kl. 21:35 (CET)
2022-12-22
OctoPrint - did a backup. Tingo (diskusjon) 22. des. 2022 kl. 20:29 (CET)
2022-08-16
the camera on Ironhive doesn't work (and has been non-working for a while now, according to sources). Unplugging and re-plugging the cable hasn't helped. Perhaps the camera or the cable is broken. Tingo (diskusjon) 16. aug. 2022 kl. 16:42 (CEST)
2022-04-18
flashed firmware to 3.11.0-4955 from OctoPrint (Firmware Updater, serial port is /dev/ttyACM0). Tingo (diskusjon) 18. apr. 2022 kl. 16:07 (CEST)
2021-06-30
flashed firmware to 3.10.0-4481 from OctoPrint (Firmware Updater). Tingo (diskusjon) 30. jun. 2021 kl. 17:36 (CEST)
opprettet bruker "bitraf" i OctoPrint, med standard passord og rolle operatør ("operator"). Tingo (diskusjon) 30. jun. 2021 kl. 17:38 (CEST)
2019-11-23
denne siden ble opprettet.

Referanser