Forskjell mellom versjoner av «CNC3-3018Pro»
Hopp til navigering
Hopp til søk
m (→Innstillinger: lenke til GRBL configuration) |
(→Innstillinger: lagt til forklaring på verdiene) |
||
| Linje 13: | Linje 13: | ||
Innstillinger og parametre satt i firmware. Se [https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration Grbl v1.1 Configuration] for mer info. | Innstillinger og parametre satt i firmware. Se [https://github.com/gnea/grbl/wiki/Grbl-v1.1-Configuration Grbl v1.1 Configuration] for mer info. | ||
| − | Settings ('$$') | + | Settings ('$$'). De som avviker fra GRBl standardverdi er merket med det. |
| − | $0=10 | + | $0=10 (step pulse, microseconds) |
| − | $1=25 | + | $1=25 (step idle delay, milliseconds) |
| − | $2=0 | + | $2=0 (step port invert, mask) |
| − | $3=5 | + | $3=5 (direction port invert, mask - grbl standardverdi er 0) |
| − | $4=0 | + | $4=0 (step enable invert, boolean) |
| − | $5=0 | + | $5=0 (limit pins invert, boolean) |
| − | $6=0 | + | $6=0 (probe pin invert, boolean) |
| − | $10=1 | + | $10=1 (status report, mask) |
| − | $11=0.010 | + | $11=0.010 (junction deviation, mm) |
| − | $12=0.002 | + | $12=0.002 (arc tolerance, mm) |
| − | $13=0 | + | $13=0 (report inches, boolean) |
| − | $20=0 | + | $20=0 (soft limits, boolean) |
| − | $21=0 | + | $21=0 (hard limits, boolean) |
| − | $22=0 | + | $22=0 (homing cycle, boolean - grbl standardverdi er 1) |
| − | $23=0 | + | $23=0 (homing dir invert, mask) |
| − | $24=25.000 | + | $24=25.000 (homing feed, mm/min) |
| − | $25=500.000 | + | $25=500.000 (homing seek, mm/min) |
| − | $26=250 | + | $26=250 (homing debounce, milliseconds) |
| − | $27=1.000 | + | $27=1.000 (homing pull-off, mm) |
| − | $30=1000 | + | $30=1000 (max spindle speed, rpm) |
| − | $31=0 | + | $31=0 (min spindle speed, rpm) |
| − | $32=0 | + | $32=0 (laser mode, boolean) |
| − | $100=800.000 | + | $100=800.000 (X steps/mm - grbl standardverdi er 250) |
| − | $101=800.000 | + | $101=800.000 (Y steps/mm - grbl standardverdi er 250) |
| − | $102=800.000 | + | $102=800.000 (Z steps/mm - grbl standardverdi er 250) |
| − | $110=800.000 | + | $110=800.000 (X max rate, mm/min - grbl standardverdi er 500) |
| − | $111=800.000 | + | $111=800.000 (Y max rate, mm/min - grbl standardverdi er 500) |
| − | $112=600.000 | + | $112=600.000 (Z max rate, mm/min - grbl standardverdi er 500) |
| − | $120=10.000 | + | $120=10.000 (X acceleration, mm/sec^2) |
| − | $121=10.000 | + | $121=10.000 (Y acceleration, mm/sec^2) |
| − | $122=10.000 | + | $122=10.000 (Z acceleration, mm/sec^2) |
| − | $130=200.000 | + | $130=200.000 (X max travel, mm) |
| − | $131=200.000 | + | $131=200.000 (Y max travel, mm) |
| − | $132=200.000 | + | $132=200.000 (Z max travel, mm) |
ok | ok | ||
parametre ('$#') | parametre ('$#') | ||
Revisjonen fra 14. nov. 2018 kl. 14:39
CNC3-3018Pro er en liten CNC-fres kjøpt som byggesett fra AliExpress[1].
Innhold
Firmware
Det er GRBL[2] versjon 1.1 som kjører på kontrollerkortet. Kommandoen '$I' (informasjon on versjon og build) melder
[VER:1.1f.20170801:] [OPT:V,15,128] ok
det er nyeste release per dags dato.
Innstillinger
Innstillinger og parametre satt i firmware. Se Grbl v1.1 Configuration for mer info.
Settings ('$$'). De som avviker fra GRBl standardverdi er merket med det.
$0=10 (step pulse, microseconds) $1=25 (step idle delay, milliseconds) $2=0 (step port invert, mask) $3=5 (direction port invert, mask - grbl standardverdi er 0) $4=0 (step enable invert, boolean) $5=0 (limit pins invert, boolean) $6=0 (probe pin invert, boolean) $10=1 (status report, mask) $11=0.010 (junction deviation, mm) $12=0.002 (arc tolerance, mm) $13=0 (report inches, boolean) $20=0 (soft limits, boolean) $21=0 (hard limits, boolean) $22=0 (homing cycle, boolean - grbl standardverdi er 1) $23=0 (homing dir invert, mask) $24=25.000 (homing feed, mm/min) $25=500.000 (homing seek, mm/min) $26=250 (homing debounce, milliseconds) $27=1.000 (homing pull-off, mm) $30=1000 (max spindle speed, rpm) $31=0 (min spindle speed, rpm) $32=0 (laser mode, boolean) $100=800.000 (X steps/mm - grbl standardverdi er 250) $101=800.000 (Y steps/mm - grbl standardverdi er 250) $102=800.000 (Z steps/mm - grbl standardverdi er 250) $110=800.000 (X max rate, mm/min - grbl standardverdi er 500) $111=800.000 (Y max rate, mm/min - grbl standardverdi er 500) $112=600.000 (Z max rate, mm/min - grbl standardverdi er 500) $120=10.000 (X acceleration, mm/sec^2) $121=10.000 (Y acceleration, mm/sec^2) $122=10.000 (Z acceleration, mm/sec^2) $130=200.000 (X max travel, mm) $131=200.000 (Y max travel, mm) $132=200.000 (Z max travel, mm) ok
parametre ('$#')
[G54:0.000,0.000,0.000] [G55:0.000,0.000,0.000] [G56:0.000,0.000,0.000] [G57:0.000,0.000,0.000] [G58:0.000,0.000,0.000] [G59:0.000,0.000,0.000] [G28:0.000,0.000,0.000] [G30:0.000,0.000,0.000] [G92:0.000,0.000,0.000] [TLO:0.000] [PRB:0.000,0.000,0.000:0] ok
Tekniske spesifikasjoner
fra produktet hos AliExpress
- working area : 30x18x4.5cm
- Frame size : 33x40x24cm
- Mesa : 30x18cm
- Spindle : 775 spindle motor (12-36V) 24V: 10000r/min
- Spindle Chuck: ER11 or normal chunk
- Step motor : Fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/M
- Power supply : 24V 5.6A
- Software : GRBL controller (Firmware GRBL v1.1)
- clamps: 4 pcs, Hold the thickness of 0-30mm,size: 50 * 20 * 3 (length * width * thick), the inner slot width 6mm
- Drill bits: tip 0.1mm ,20 degree , diameter3.175mm.the package include 10pc
vår maskin er uten opsjon for laser.
Strømforsyningen er ekstern ("laptop type"), Lite-On EPS-5, model EADP-75GB A. Inn: 100 - 240 V AC, 50 - 60 Hz, ~ 1.3A. Ut: 24 V DC (center positive), 5A. Strømkabelen er en med liggende-åttetall plugg ("barbermaskin type") i ene enden, og USA-plugg + adapter i andre enden.
Dokumentasjon
- Fil:GRBL software Instructions CNC3-3018Pro.pdf
- Fil:Woodpecker CNC User Manual V1.1 CNC3-3018Pro.pdf
