CNC3-3018Pro/testing
Tilbake til CNC3-3018Pro.
Denne undersiden dokumenterer testing av maskinen.
Historikk
- 2018-11-14
- installert UGS[1] (platform) og testet. Det går an å jogge aksene på maskinen frem og tilbake ved hjelp av UGS. Tingo (diskusjon) 14. nov. 2018 kl. 16:26 (CET)
- koblet fra den manuelle kontrolleren, og koblet til via medfølgende usb-kabel (USB A til mini B). Nå funker GRBL.
Grbl 1.1f ['$' for help] ok
og jeg kan sende kommandoer. '$' gir
[HLP:$$ $# $G $I $N $x=val $Nx=line $J=line $SLP $C $X $H ~ ! ? ctrl-x] ok
current status ('?')
<Idle|MPos:0.000,0.000,0.000|FS:0,0|WCO:0.000,0.000,0.000>
version or build info ('$I')
[VER:1.1f.20170801:] [OPT:V,15,128] ok
view parser state ('$G')
[GC:G0 G54 G17 G21 G90 G94 M5 M9 T0 F0 S0] ok
view settings ('$$')
$0=10 $1=25 $2=0 $3=5 $4=0 $5=0 $6=0 $10=1 $11=0.010 $12=0.002 $13=0 $20=0 $21=0 $22=0 $23=0 $24=25.000 $25=500.000 $26=250 $27=1.000 $30=1000 $31=0 $32=0 $100=800.000 $101=800.000 $102=800.000 $110=800.000 $111=800.000 $112=600.000 $120=10.000 $121=10.000 $122=10.000 $130=200.000 $131=200.000 $132=200.000 ok
view # parameters ('$#')
[G54:0.000,0.000,0.000] [G55:0.000,0.000,0.000] [G56:0.000,0.000,0.000] [G57:0.000,0.000,0.000] [G58:0.000,0.000,0.000] [G59:0.000,0.000,0.000] [G28:0.000,0.000,0.000] [G30:0.000,0.000,0.000] [G92:0.000,0.000,0.000] [TLO:0.000] [PRB:0.000,0.000,0.000:0] ok
view startup blocks ('$N')
$N0= $N1= ok
that's pretty much it.
- 2018-11-13
- koblet 3018Pro til en datamaskin (med Debian 9.5) ved hjelp av usb-kabelen som fulgte med. i /var/log/messages:
Nov 13 17:43:05 kg-bsbox kernel: [441161.598183] usb 1-1.1: new full-speed USB device number 9 using xhci_hcd Nov 13 17:43:06 kg-bsbox kernel: [441161.718819] usb 1-1.1: New USB device found, idVendor=1a86, idProduct=7523, bcdDevice= 2.54 Nov 13 17:43:06 kg-bsbox kernel: [441161.718822] usb 1-1.1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 Nov 13 17:43:06 kg-bsbox kernel: [441161.718823] usb 1-1.1: Product: USB2.0-Serial Nov 13 17:43:06 kg-bsbox kernel: [441161.720497] ch341 1-1.1:1.0: ch341-uart converter detected Nov 13 17:43:06 kg-bsbox kernel: [441161.720854] usb 1-1.1: ch341-uart converter now attached to ttyUSB0
og den dukker opp som en usb serial device
tingo@kg-bsbox:~$ ls -l /dev/tty[ACU]* crw-rw---- 1 root dialout 188, 0 Nov 13 17:43 /dev/ttyUSB0
det er en bra start. Tingo (diskusjon) 13. nov. 2018 kl. 17:48 (CET)
- kobler til med pronterface (115200 baud) og får
Grbl 1.1f ['$' for help] Printer is now online.
hvis jeg sender '$'
>>> $ SENDING:$ [WARNING] raw G-Code line "$" could not be parsed
ok, hva med andre kommandoer da?
>>> $$ SENDING:$$ [WARNING] raw G-Code line "$$" could not be parsed >>> $$ SENDING:$$ [WARNING] raw G-Code line "$$" could not be parsed Reset. >>> $# SENDING:$# [WARNING] raw G-Code line "$#" could not be parsed
ikke så bra.
>>> $X SENDING:$X
ingen feilmelding i det minste.
>>> ? Documented commands (type help <topic>): ======================================== bedtemp eta help monitor reset sdprint tool block_until_online exit home move resume set upload button extrude load off reverse settemp connect gcodes ls pause run_gcode_script shell disconnect gettemp macro print run_script slice Undocumented commands: ====================== editgcode extrude_final pront_extrude pront_reverse setspeed
hmm, kanskje pronterface lurer meg. Tingo (diskusjon) 13. nov. 2018 kl. 17:57 (CET)
- selv med screen ('screen /dev/ttyUSB0 115200') så virker det ikke. Får oppstartsmelding
Grbl 1.1f ['$' for help]
men den tar ikke i mot kommandoer. Hver gang jeg trykker på reset-knappen på kontrollkortet får jeg en oppstartsmelding
Grbl 1.1f ['$' for help] Grbl 1.1f ['$' for help]
ok, mer testing i morgen. Tingo (diskusjon) 13. nov. 2018 kl. 18:48 (CET)
- 2018-11-12
- testet maskinen, med strøm og manuell kontroller. Jogging og spindle start / stopp fungerer. Tingo (diskusjon)
Referanser
andre interessante lenker
