Forskjell mellom versjoner av «Metroplex 3D printer/bygging»

Fra Bitraf
Hopp til navigering Hopp til søk
(Historikk: better formatting of image)
(Historikk: soldered connectors to the connector board)
Linje 2: Linje 2:
  
 
== Historikk ==
 
== Historikk ==
 +
; 2019-04-04 : today (finally!) I soldered connectors to the connector board. [[Image:Connector board soldered 20190404 142328.jpg|100px]]. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 4. apr. 2019 kl. 14:28 (CEST)
 +
 
; 2019-02-28 : using the CNC3-3018Pro, I made a small connector board for the printer.
 
; 2019-02-28 : using the CNC3-3018Pro, I made a small connector board for the printer.
 
[[Image:V-bit 10 degrees 1pass 20190228 220122.jpg|100px|connector board]] [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 4. apr. 2019 kl. 14:17 (CEST)
 
[[Image:V-bit 10 degrees 1pass 20190228 220122.jpg|100px|connector board]] [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 4. apr. 2019 kl. 14:17 (CEST)

Revisjonen fra 4. apr. 2019 kl. 13:29

Tilbake til Metroplex 3D printer.

Historikk

2019-04-04 
today (finally!) I soldered connectors to the connector board. Connector board soldered 20190404 142328.jpg. Tingo (diskusjon) 4. apr. 2019 kl. 14:28 (CEST)
2019-02-28 
using the CNC3-3018Pro, I made a small connector board for the printer.

connector board Tingo (diskusjon) 4. apr. 2019 kl. 14:17 (CEST)

2019-01-23 
Elias and I tapped threads in the center holes of the aluminum rods, and screwed the top plate on. The cabling was moved, it needs to find a new home under or inside the aluminium rods at the top. Next we tapped threads for the bottom plate and screwed that on. Both operations required adjusting the length between the corners a bit. Finally we mounted the plate underneath the printbed. Because of the length adjustments between corners, the holes didn't fit, so we had to drill new holes. As usual pictures in the gallery below. Tingo (diskusjon) 23. jan. 2019 kl. 17:58 (CET)
2019-01-22 
the Precision Piezo Universal Z-probe Kit[1] that Jon C sent arrived. Thanks! Tingo (diskusjon) 22. jan. 2019 kl. 15:50 (CET) Tip from Jon C "Make sure to put a few millimeters of wood or silicone pads to insulate from the heat." Tingo (diskusjon)
I dag har Elias og jeg frest ut topp-, bunn- og baseplater[2] til Metroplex. Se bilder lenger ned. Tingo (diskusjon) 22. jan. 2019 kl. 15:37 (CET)
2019-01-15 - 2019-01-18 
learning to use FreeCAD, I create (with help from others) design for a bottom plate (sits between the frame and the print bed), a top plate and a base plate (under the printer). Tingo (diskusjon) 21. jan. 2019 kl. 14:29 (CET)
2019-01-14 
Elias and I (with lots of help from other with more CNC experience) plane down a round aluminum plate that will be used as print bed for the Monster Kossel.
2019-01-10 
the Monster Kossel gets a name: Metroplex[3].
2019, first week of January 
Jon C. comes to Bitraf and builds the Monster Kossel. He has put some pictures of the build here[4].

Bilder

Topp-, bunn- og baseplate montert.

Lage plater til topp, bunn (under printplate) og base (under printeren).

Fresing (planering) av aluminium printbed.

Referanser