Forskjell mellom versjoner av «Hattori/grbl»
Hopp til navigering
Hopp til søk
(→Settings - Hattori: lagt inn settings fra grbl på Hattori slik de er nå.) |
(→Settings - Hattori: lagt inn gcode parametre fra Hattori) |
||
Linje 42: | Linje 42: | ||
ok | ok | ||
settings per 2017-07-10. | settings per 2017-07-10. | ||
+ | === gcode parameters === | ||
+ | Med '$#' får du listet ut g-code parametre. | ||
+ | >>> $# | ||
+ | [G54:-11.000,-90.997,-17.100] | ||
+ | [G55:0.000,0.000,0.000] | ||
+ | [G56:0.000,0.000,0.000] | ||
+ | [G57:0.000,0.000,0.000] | ||
+ | [G58:0.000,0.000,0.000] | ||
+ | [G59:0.000,0.000,0.000] | ||
+ | [G28:0.000,0.000,0.000] | ||
+ | [G30:0.000,0.000,0.000] | ||
+ | [G92:0.000,0.000,0.000] | ||
+ | [TLO:0.000] | ||
+ | [PRB:0.000,0.000,0.000:0] | ||
+ | ok | ||
+ | gcode parametre per 2017-07-10. | ||
== Settings - standardverdier == | == Settings - standardverdier == | ||
[[Category:CNC]] [[Category:grbl]] | [[Category:CNC]] [[Category:grbl]] |
Revisjonen fra 10. jul. 2017 kl. 10:58
Tilbake til Hattori.
Denne undersiden beskriver hvordan grbl konfigureres for Hattori.
Settings - Hattori
Kommandoen for å vise settings i grbl er '$$'.
>>> $$ $0 = 10 (Step pulse time, microseconds) $1 = 255 (Step idle delay, milliseconds) $2 = 0 (Step pulse invert, mask) $3 = 5 (Step direction invert, mask) $4 = 0 (Invert step enable pin, boolean) $5 = 0 (Invert limit pins, boolean) $6 = 0 (Invert probe pin, boolean) $10 = 1 (Status report options, mask) $11 = 0.010 (Junction deviation, millimeters) $12 = 0.002 (Arc tolerance, millimeters) $13 = 0 (Report in inches, boolean) $20 = 0 (Soft limits enable, boolean) $21 = 0 (Hard limits enable, boolean) $22 = 1 (Homing cycle enable, boolean) $23 = 3 (Homing direction invert, mask) $24 = 200.000 (Homing locate feed rate, mm/min) $25 = 6000.000 (Homing search seek rate, mm/min) $26 = 250 (Homing switch debounce delay, milliseconds) $27 = 4.000 (Homing switch pull-off distance, millimeters) $30 = 1000 (Maximum spindle speed, RPM) $31 = 0 (Minimum spindle speed, RPM) $32 = 0 (Laser-mode enable, boolean) $100 = 88.888 (X-axis travel resolution, step/mm) $101 = 88.888 (Y-axis travel resolution, step/mm) $102 = 88.888 (Z-axis travel resolution, step/mm) $110 = 12000.000 (X-axis maximum rate, mm/min) $111 = 12000.000 (Y-axis maximum rate, mm/min) $112 = 3000.000 (Z-axis maximum rate, mm/min) $120 = 1200.000 (X-axis acceleration, mm/sec^2) $121 = 1200.000 (Y-axis acceleration, mm/sec^2) $122 = 300.000 (Z-axis acceleration, mm/sec^2) $130 = 120.000 (X-axis maximum travel, millimeters) $131 = 180.000 (Y-axis maximum travel, millimeters) $132 = 120.000 (Z-axis maximum travel, millimeters) ok
settings per 2017-07-10.
gcode parameters
Med '$#' får du listet ut g-code parametre.
>>> $# [G54:-11.000,-90.997,-17.100] [G55:0.000,0.000,0.000] [G56:0.000,0.000,0.000] [G57:0.000,0.000,0.000] [G58:0.000,0.000,0.000] [G59:0.000,0.000,0.000] [G28:0.000,0.000,0.000] [G30:0.000,0.000,0.000] [G92:0.000,0.000,0.000] [TLO:0.000] [PRB:0.000,0.000,0.000:0] ok
gcode parametre per 2017-07-10.