Forskjell mellom versjoner av «Hattori/grbl»
Hopp til navigering
Hopp til søk
m (subpages er off, så jeg må legge inn "tilbake" lenke manuelt) |
(→Settings - Hattori: lagt inn settings fra grbl på Hattori slik de er nå.) |
||
Linje 4: | Linje 4: | ||
== Settings - Hattori == | == Settings - Hattori == | ||
+ | Kommandoen for å vise settings i grbl er '$$'. | ||
+ | >>> $$ | ||
+ | $0 = 10 (Step pulse time, microseconds) | ||
+ | $1 = 255 (Step idle delay, milliseconds) | ||
+ | $2 = 0 (Step pulse invert, mask) | ||
+ | $3 = 5 (Step direction invert, mask) | ||
+ | $4 = 0 (Invert step enable pin, boolean) | ||
+ | $5 = 0 (Invert limit pins, boolean) | ||
+ | $6 = 0 (Invert probe pin, boolean) | ||
+ | $10 = 1 (Status report options, mask) | ||
+ | $11 = 0.010 (Junction deviation, millimeters) | ||
+ | $12 = 0.002 (Arc tolerance, millimeters) | ||
+ | $13 = 0 (Report in inches, boolean) | ||
+ | $20 = 0 (Soft limits enable, boolean) | ||
+ | $21 = 0 (Hard limits enable, boolean) | ||
+ | $22 = 1 (Homing cycle enable, boolean) | ||
+ | $23 = 3 (Homing direction invert, mask) | ||
+ | $24 = 200.000 (Homing locate feed rate, mm/min) | ||
+ | $25 = 6000.000 (Homing search seek rate, mm/min) | ||
+ | $26 = 250 (Homing switch debounce delay, milliseconds) | ||
+ | $27 = 4.000 (Homing switch pull-off distance, millimeters) | ||
+ | $30 = 1000 (Maximum spindle speed, RPM) | ||
+ | $31 = 0 (Minimum spindle speed, RPM) | ||
+ | $32 = 0 (Laser-mode enable, boolean) | ||
+ | $100 = 88.888 (X-axis travel resolution, step/mm) | ||
+ | $101 = 88.888 (Y-axis travel resolution, step/mm) | ||
+ | $102 = 88.888 (Z-axis travel resolution, step/mm) | ||
+ | $110 = 12000.000 (X-axis maximum rate, mm/min) | ||
+ | $111 = 12000.000 (Y-axis maximum rate, mm/min) | ||
+ | $112 = 3000.000 (Z-axis maximum rate, mm/min) | ||
+ | $120 = 1200.000 (X-axis acceleration, mm/sec^2) | ||
+ | $121 = 1200.000 (Y-axis acceleration, mm/sec^2) | ||
+ | $122 = 300.000 (Z-axis acceleration, mm/sec^2) | ||
+ | $130 = 120.000 (X-axis maximum travel, millimeters) | ||
+ | $131 = 180.000 (Y-axis maximum travel, millimeters) | ||
+ | $132 = 120.000 (Z-axis maximum travel, millimeters) | ||
+ | ok | ||
+ | settings per 2017-07-10. | ||
== Settings - standardverdier == | == Settings - standardverdier == | ||
[[Category:CNC]] [[Category:grbl]] | [[Category:CNC]] [[Category:grbl]] |
Revisjonen fra 10. jul. 2017 kl. 10:52
Tilbake til Hattori.
Denne undersiden beskriver hvordan grbl konfigureres for Hattori.
Settings - Hattori
Kommandoen for å vise settings i grbl er '$$'.
>>> $$ $0 = 10 (Step pulse time, microseconds) $1 = 255 (Step idle delay, milliseconds) $2 = 0 (Step pulse invert, mask) $3 = 5 (Step direction invert, mask) $4 = 0 (Invert step enable pin, boolean) $5 = 0 (Invert limit pins, boolean) $6 = 0 (Invert probe pin, boolean) $10 = 1 (Status report options, mask) $11 = 0.010 (Junction deviation, millimeters) $12 = 0.002 (Arc tolerance, millimeters) $13 = 0 (Report in inches, boolean) $20 = 0 (Soft limits enable, boolean) $21 = 0 (Hard limits enable, boolean) $22 = 1 (Homing cycle enable, boolean) $23 = 3 (Homing direction invert, mask) $24 = 200.000 (Homing locate feed rate, mm/min) $25 = 6000.000 (Homing search seek rate, mm/min) $26 = 250 (Homing switch debounce delay, milliseconds) $27 = 4.000 (Homing switch pull-off distance, millimeters) $30 = 1000 (Maximum spindle speed, RPM) $31 = 0 (Minimum spindle speed, RPM) $32 = 0 (Laser-mode enable, boolean) $100 = 88.888 (X-axis travel resolution, step/mm) $101 = 88.888 (Y-axis travel resolution, step/mm) $102 = 88.888 (Z-axis travel resolution, step/mm) $110 = 12000.000 (X-axis maximum rate, mm/min) $111 = 12000.000 (Y-axis maximum rate, mm/min) $112 = 3000.000 (Z-axis maximum rate, mm/min) $120 = 1200.000 (X-axis acceleration, mm/sec^2) $121 = 1200.000 (Y-axis acceleration, mm/sec^2) $122 = 300.000 (Z-axis acceleration, mm/sec^2) $130 = 120.000 (X-axis maximum travel, millimeters) $131 = 180.000 (Y-axis maximum travel, millimeters) $132 = 120.000 (Z-axis maximum travel, millimeters) ok
settings per 2017-07-10.