Forskjell mellom versjoner av «Laserfilter»
(12 mellomliggende revisjoner av en annen bruker er ikke vist) | |||
Linje 1: | Linje 1: | ||
The laser cutters @ Bitraf have one filter each: | The laser cutters @ Bitraf have one filter each: | ||
− | * The small Redsail X700 (50x70cm cutting area @ 60W) uses the "Bofa AD Oracle IQ" | + | * The small Redsail X700 (50x70cm cutting area @ 60W) uses the "Bofa<ref>[https://bofainternational.com/ BOFA International]</ref> AD Oracle IQ" |
* The larger Redsail X900 (70x90cm cutting area @ 110W) uses a "Bofa AD1000 IQ" | * The larger Redsail X900 (70x90cm cutting area @ 110W) uses a "Bofa AD1000 IQ" | ||
Linje 7: | Linje 7: | ||
The smaller was purchased from Alvøen. The larger from Vodex in the UK. The UK price is about half the Norwegian price, so certainly worth checking out. | The smaller was purchased from Alvøen. The larger from Vodex in the UK. The UK price is about half the Norwegian price, so certainly worth checking out. | ||
− | = Building your own = | + | == Maintenance == |
− | Before buying commercial filter unit, we tried building our own filter. This is really hard as you need to force a lot of air through at least a coal filter + a particle filter of som sort. For large machines, you need a very | + | From FAQ section on BOFA web "All local exhaust ventilation (LEV) systems should be thoroughly examined and tested by a qualified engineer at least every 14 months - some process may mean that your unit requires much more frequent servicing." |
+ | |||
+ | From the operator manual: "User maintenance is limited to cleaning the unit and replacing the filters with new. | ||
+ | Only BOFA International trained maintenance technicians are authorised to carry out | ||
+ | component testing and replacement. Unauthorised work or the use of unauthorised | ||
+ | replacement filters may result in a potentially dangerous situation and/or damage to | ||
+ | the extractor unit, and will invalidate the manufacturer‟s warranty." | ||
+ | |||
+ | == Maintenance log == | ||
+ | Write an entry every time a filter is exchanged, or some other maintenance is pperformed. | ||
+ | |||
+ | ; 2021-10-28 : Øverste filter byttet av Vegard Holter [[Bruker:Jenny|Jenny]] ([[Brukerdiskusjon:Jenny|diskusjon]]) 15. nov. 2021 kl. 17:14 (CET) | ||
+ | |||
+ | ; 2021-11-11 : Nederste filter byttet av Vegard Holter [[Bruker:Jenny|Jenny]] ([[Brukerdiskusjon:Jenny|diskusjon]]) 15. nov. 2021 kl. 17:14 (CET) | ||
+ | |||
+ | ; YYYY-MM-DD : Operation performed, result if needed. At the end of your entry, put four '~' characters after each other, then the entry will have your username and a timestamp on it. [[Bruker:Tingo|Tingo]] ([[Brukerdiskusjon:Tingo|diskusjon]]) 9. nov. 2021 kl. 20:21 (CET) | ||
+ | |||
+ | == Building your own == | ||
+ | Before buying commercial filter unit, we tried building our own filter. This is really hard as you need to force a lot of air through at least a coal filter + a particle filter of som sort. For large machines, you need a very powerful fan to force air through these. You also need to consider that getting hold of new filters must be quite easy also. It's much, much easier to keep tools in a working state if more than one person can help. Calling a supplier rather than running around thttps://bofainternational.com/own to source required parts only pays off if you have a very low hourly rate and not much else to do... | ||
After giving up on our own filter, we just ventilated into the backyard. Blowing out a large volume of heated air really does something to your heating costs, but the reason we had to get a filter was that the neighbours complained when we were cutting plastics. | After giving up on our own filter, we just ventilated into the backyard. Blowing out a large volume of heated air really does something to your heating costs, but the reason we had to get a filter was that the neighbours complained when we were cutting plastics. | ||
+ | |||
+ | == Documentation == | ||
+ | * AD 500, 1000, 1500 Operator manual<ref>[[Fil:Ad 500 1000 1500 instruction manual 39473.pdf]]</ref> | ||
+ | * AD 1000 IQ data sheet<ref>[[Fil:AD 1000 IQ.pdf]]</ref> | ||
+ | * AD Oracle Operator manual<ref>[[Fil:Ad oracle manual.pdf]]</ref> | ||
+ | * AD Oracle IQ data sheet<ref>[[Fil:Ad-oracle-iq-1850.pdf]]</ref> | ||
+ | |||
+ | == References == | ||
+ | <references/> | ||
+ | |||
+ | [[Category:Laserkutter]] |
Nåværende revisjon fra 15. nov. 2021 kl. 17:14
The laser cutters @ Bitraf have one filter each:
- The small Redsail X700 (50x70cm cutting area @ 60W) uses the "Bofa[1] AD Oracle IQ"
- The larger Redsail X900 (70x90cm cutting area @ 110W) uses a "Bofa AD1000 IQ"
It's not feasible to let one filter run more than one machine due to the volume of air that you need to pull through. Swapping the filters are as easy as opening the lock, turning a handle and pulling out the old filter. Just do it in reverse to add the new one.
The smaller was purchased from Alvøen. The larger from Vodex in the UK. The UK price is about half the Norwegian price, so certainly worth checking out.
Maintenance
From FAQ section on BOFA web "All local exhaust ventilation (LEV) systems should be thoroughly examined and tested by a qualified engineer at least every 14 months - some process may mean that your unit requires much more frequent servicing."
From the operator manual: "User maintenance is limited to cleaning the unit and replacing the filters with new. Only BOFA International trained maintenance technicians are authorised to carry out component testing and replacement. Unauthorised work or the use of unauthorised replacement filters may result in a potentially dangerous situation and/or damage to the extractor unit, and will invalidate the manufacturer‟s warranty."
Maintenance log
Write an entry every time a filter is exchanged, or some other maintenance is pperformed.
- YYYY-MM-DD
- Operation performed, result if needed. At the end of your entry, put four '~' characters after each other, then the entry will have your username and a timestamp on it. Tingo (diskusjon) 9. nov. 2021 kl. 20:21 (CET)
Building your own
Before buying commercial filter unit, we tried building our own filter. This is really hard as you need to force a lot of air through at least a coal filter + a particle filter of som sort. For large machines, you need a very powerful fan to force air through these. You also need to consider that getting hold of new filters must be quite easy also. It's much, much easier to keep tools in a working state if more than one person can help. Calling a supplier rather than running around thttps://bofainternational.com/own to source required parts only pays off if you have a very low hourly rate and not much else to do...
After giving up on our own filter, we just ventilated into the backyard. Blowing out a large volume of heated air really does something to your heating costs, but the reason we had to get a filter was that the neighbours complained when we were cutting plastics.
Documentation
- AD 500, 1000, 1500 Operator manual[2]
- AD 1000 IQ data sheet[3]
- AD Oracle Operator manual[4]
- AD Oracle IQ data sheet[5]