Bitraf - Brukerbidrag [nb]

Band saw English

2026-08-15T20:24:23Z

Skairunner: /* After cutting */ Remember to turn off the machine

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
(Normally uses a 13mm blade)
Cabinet ......... Close
Guides .......... Set
(Reference posted on cabinet)
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
Clothing ........ Remove any loose, dangling
Tie hair if long
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Machine ......... Off
Cable plug ...... Remove, lock
Table ........... Reset to level
Debris .......... Remove
Dust ............ Remove with vacuum
(Check table, upper cabinet,
blade guard cabinet, lower cabinet)
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Band saw English

2026-08-15T20:17:15Z

Skairunner: /* Before cutting */ add clothing check item

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
(Normally uses a 13mm blade)
Cabinet ......... Close
Guides .......... Set
(Reference posted on cabinet)
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
Clothing ........ Remove any loose, dangling
Tie hair if long
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Table ........... Reset to level
Cable plug ...... Remove, lock
Debris .......... Remove
Dust ............ Remove with vacuum
(Check table, upper cabinet,
blade guard cabinet, lower cabinet)
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Band saw English

2026-08-15T20:15:09Z

Skairunner: /* After cutting */ Format note

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
(Normally uses a 13mm blade)
Cabinet ......... Close
Guides .......... Set
(Reference posted on cabinet)
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Table ........... Reset to level
Cable plug ...... Remove, lock
Debris .......... Remove
Dust ............ Remove with vacuum
(Check table, upper cabinet,
blade guard cabinet, lower cabinet)
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Band saw English

2026-08-15T20:14:52Z

Skairunner: /* Before plugging in */ formatting of previously italic text

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
(Normally uses a 13mm blade)
Cabinet ......... Close
Guides .......... Set
(Reference posted on cabinet)
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Table ........... Reset to level
Cable plug ...... Remove, lock
Debris .......... Remove
Dust ............ Remove with vacuum
Check table, upper cabinet,
blade guard cabinet, lower cabinet
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Band saw English

2026-08-15T20:14:15Z

Skairunner: /* Before plugging in */ cant use italics in pre :(

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
Normally uses a 13mm blade
Cabinet ......... Close
Guides .......... Set
Reference posted on cabinet
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Table ........... Reset to level
Cable plug ...... Remove, lock
Debris .......... Remove
Dust ............ Remove with vacuum
Check table, upper cabinet,
blade guard cabinet, lower cabinet
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Band saw English

2026-08-15T20:12:43Z

Skairunner: Add checklist

{| class="wikitable"
|-
[[Band_saw|Norsk versjon her]]
|}
=Basic bandsaw usage=
==Safety and general usage==
===Before using the bandsaw===
[[Fil:Posisjon for hendel til bladspenning.jpg|miniatyr|Figure 1 - Lever A must always be in a horizontal position when using the bandsaw (Full tension)..]]
[[Fil:Båndsag bladspenning innstilling.jpg|miniatyr|Figure 2 - Bandsaw blade tension scale and blade tension handwheel..]]
[[Fil:Bandsaw blade tension scale.JPG|miniatyr|Figure 3 - Bandsaw blade tension scale set for 13 mm blade..]]
[[Fil:Stille bladstyringens høyde.jpg|miniatyr|Figure 4: Adjust height of blade guide by using locking knoB B and wheel C.]]
[[Fil:AV- og på-knapper.jpg|miniatyr|Figure 5: On and off buttons.]]
[[Fil:Låsehendel for å stille vinkel på sagbordet.jpg|miniatyr|Figure 6: Angle of saw table is done by loosening lever D, adjusting table angle and tightening the lock lever D again.]]
[[Fil:Anlegg i vertikal stilling .jpg|miniatyr|Figure 7: Upright position of fence. Use knobs E to loosen and fasten the fence.]]
[[Fil:Anlegg i horisontal stilling.jpg|miniatyr|Figure 8: Fence in horisontal position.]]
[[Fil:Finjustering av anlegg.jpg|miniatyr|Figure 9: Fine adjustment of fence.]]
[[Fil:Buede kutt sages i segmenter.jpg|miniatyr|Figure 10: Curves are sawn in segments if if the approximate "straight" area is less than 1,5 cm.]]

Never connect power to a machine before you have made a preliminary check everything is in order with the machine. 

Always write in Bitraf's calendar: name, tool (Bandsaw), phone number, date and time from and until which you will use the tool. Access to the calendar and how it is used can be found here: [[https://wiki.bitraf.no/wiki/Booking]]. 

- Check inside the saw if the person using the bandsaw before you has cleaned it after usie, if not clean before you start. 
- Connect vacuum cleaner to saw. 
- Check if the blade is sharp - feel with a finger - if the blade is dull - stop work. 

Lever A (Figure 1) at the back of the band saw must always be in a horizontal position when the saw is in use. Then the saw blade will be under tension. 
Check if the red blade tension needle shows the correct blade tension for the blade mounted on the saw. Turn the blade tension handwheel to adjust if necessary (Figure 2 and 3).
The bandsaw is will usually be fitted with a blade which is 13mm wide with 4 TPI (teeth per inch)). 

With the saw blade that is usually found on the band saw, you should only cut wood and plastic materials. It is not recommended to rip thick boards with this blade. 

Check out key # 6 to unlock the band saw if everything is in order. 

==Safety and usage==
Do not use any machines at Bitraf if you are tired or under the influence of alcohol or other drugs. 
Never walk away from a running machine without supervision. 
Remove ties, scarves, rings, watches and other jewelery before using the band saw. Also put up long hair. 
Always keep fingers (and other body parts, including hair and beard) outside the black circle around the saw blade. 

Gloves, loose sleeves and loose clothing should not be used when working with rotating tools – including bandsaws! 

Use a dust mask, safety glasses and hearing protection! Tinnitus, damaged hearing and damaged vision are not cool! 
Fine dust particles that you breathe in can cause discomfort and an increased risk of cancer and lung diseases. 

Use a push stick and/or push block when cutting small or narrow workpieces! 

Be concentrated on the work, not on other things when using machines. If you are going to talk to others, turn off the saw. 

Do not work with the wood upright or in any other unusual positions without support. Round objects and other materials that do not lie flat against the saw table and/or fence must be attached to other materials with screws or clamps for stability!

Bandsaw blades are subjected to high stresses and breakage are sometimes unavoidable. Some common causes of blade breakage are: 
- you use a too wide blade to cut a curve with a small radius 
- you use too much force to guide the workpiece towards the blade - instead, let the blade work through the material without using force 
- upper blade guide too high above the work piece 
- blunt or uncorrectly set saw blade teeth 
- incorrectly adjusted blade guides 
- too high blade tension 
- fault in the blade welding joint 

Should the machine start making strange noises - stand back and press the red stop button (Figure 5). 

Small pieces of wood are removed from the saw table after the saw blade has stopped – '''not before'''! 

===Adjust angle of the saw table===
Disconnect the power from the band saw. 
Release locking lever D (Figure 6). The saw table can be tilted up to 45 degrees towards the right seen from the front. Tighten locking lever D when you have the angle you want. 
Remember to return the saw table to the horizontal position when you are finished. 

===Position on fence and rail===
The fence can stand upright or lie flat on the saw table. Use the screw knobs E (Figure 7 and 8) to loosen and fasten the fence. 

===Fine-tuning of fence position===
Loosen the fencevwith locking knob F and small knob G under the rail (Figure 9). Push the fence to the approximately desired position and lock it to the rail with small knob G. Fine-tune with millimeter wheel H and lock with locking knob F. 

===Straight cuts===
Feed the workpiece straight ahead, possibly by using the fence as a sideways support. 

===Curved cuts===
DO NOT force the tool to do something it cannot do. When the regular saw blade that is mounted on the saw, you cannot saw arcs where the "approximately straight" area is less than 1.5 cm. Arches must then be sawn in segments with relief cuts from the side towards the arch as shown (Figure 10). 

Can't be said too often: Gloves and loose (sleeves on) clothing should absolutely not be used on any rotating tool – band saw included! 

Some things to be aware of: 
Thick or tall materials put extra wear and tear on the saw blade - write a message on the Woodwork channel on Slack or to someone responsible for the tool so we can check if it needs to be replaced! 

Since the blade on the band saw moves down towards the saw table, the general risk of kickback is small compared to table saws. '''BUT:''' you still have to be careful with round objects, refer to what is written in the "Safety and use" section about working with the material upright or in unusual positions without support. 

===Adjust the upper blade guide to the correct height===
Before you start the saw, set the blade guide to the correct height for the job you're going to do. 

You do this by loosening lock knob B (Figure 4). You then adjust the blade guide to the correct height for what you are going to saw by turning the wheel C. Lock the blade guide by turning the locking knob B. 

For straight cuts, the blade guard should be as close to the workpiece as possible, approx. 2.5 cm above the workpiece. 

If you need to cut curves, the blade guard can be raised. With the blade guard 10-15 cm above the workpiece, you can have a good view of what you're dooing. 

The purpose of the protective housing on the saw blade is to protect the user and to stabilize the saw blade laterally. 

When these checks have been completed, you are "good to go"! 

Connect power to band saw. 
Connect a vacuum cleaner if you haven't already. 
Turn on the vacuum cleaner. 

Start the saw by holding the green on button for ½ second (Figure 5).

===Practical exercise===
Find a piece of wood and try a couple of cuts on the saw! 

Small pieces on the saw table: Stop the machine '''BEFORE''' you remove them! 
Burn marks in thin panels: Could be a problem with a worn saw blade! 

==When finished using the band saw==
Unplug the power to the band saw and put the lock on the plug. 

Always clean the tool and the floor around after you! Open and clean inside the saw. Use compressed air in places that are difficult to access, and vacuum cleaner where you reach. Clean the saw blade if there is a lot of dirt on it. Then the person using the saw after you're finished doesn't have to spend their time cleaning up after you - this contributes to a healthy environment at Bitraf! Remember the "do-o-cracy" at Bitraf! 

If someone has forgotten to clean - clean up after them too, since this contributes to Bitraf beeing a nice place to come - and people perhaps also to treat our equipment better. 

Finish off by checking in the key. 

{{float end}}

=Quick reference=
A simplified checklist for quick reference.

==Before plugging in==
<pre>
Calendar ........ Name, tool, phone number
Tension lever ... Horizontal
Blade ........... Sharp
Cabinet ......... Check upper, lower clean
Tension scale ... Set
Normally uses a 13mm blade
Cabinet ......... Close
Guides .......... Set
Reference posted on cabinet
Key ............. Check out
Vacuum hose ..... Set and on
Cable plug ...... Unlock, insert
</pre>

==Before cutting==
<pre>
Jig ............. Set
Table ........... Adjust if needed
Blade guard ..... Set
PPE ............. Eyepro, earpro, dust mask
Machine ......... On
</pre>

DO NOT REMOVE DEBRIS WHILE SAW IS ACTIVE.

==After cutting==
<pre>
Table ........... Reset to level
Cable plug ...... Remove, lock
Debris .......... Remove
Dust ............ Remove with vacuum
Check table, upper cabinet,
blade guard cabinet, lower cabinet
Cabinet ......... Close
Key ............. Return
</pre>

== References ==
<references/>

[[Fil:Manual-JWBS-18SFXBandSaw UM EN ED4 1.pdf|miniatyr|Manual for Bitrafs bandsaw.]] 

[[Category:Utstyr]]

Mal:Float end

2026-08-15T20:12:23Z

Skairunner: make it actually work

<onlyinclude><div style="clear: both"></div></onlyinclude>

A template to cleaf float. Useful for controlling images.

Mal:Float end

2026-08-15T20:08:58Z

Skairunner:

<onlyinclude></onlyinclude>

A template to set float to none. Useful for controlling images.

Mal:Float end

2026-08-15T20:08:19Z

Skairunner: Ny side: <onlyinclude></onlyinclude> A template to end float.

<onlyinclude></onlyinclude>

A template to end float.

Utstyr på Bitraf

2026-08-15T17:59:16Z

Skairunner: /* Snekkerverksted */ We don't seem to have a sirkelsag anymore

Utstyr som er tilgjengelig for medlemmer på bitraf. Utstyr er ikke til hjemlån.

 
'''Booking:''' [[Booking|Reserver maskiner her]]
 

== Trykkluft i alle rom ==
Hurtigkobbling sitter på vegger runt om i hele bitrafs lokaler. CEJN 310 er typen kobbling som passer.
tex: CEJN 310 5003 er en hurtigkobbling med slangippel.

== Utstyr i labben ==
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 2 || Datamaskin || Bitraf ||[[Felles PC]]||Nei||Nei
|-
| 5 || Oscilloskop<ref>[https://www.thingiverse.com/thing:2516749 Rigol DS1052E replacement knob small]</ref> || - || -||Nei||Nei
|-
| 1 || Saleae Logic (Logikk-analysator) || [[Bruker:Trygvis|Trygvis]] ||-||Nei||Nei
|-
| 1 || [[lodding|Loddestasjon]] m/varmluft Aoyue 968a || - || -||Nei||Nei
|-
| 1 || ZD-987 Lodde- og utloddestasjon (vakuum) || [[User:Tingo|Torfinn]] || [[Puctec ZD-987|Instruksjoner]] ||Nei||Nei
|-
| 4 || 30W Loddebolt || Bitraf || -||Nei||Nei
|-
| 1 || Mikroskop || - ||-||Nei||Nei
|-
| 2 || Lampe m/lupe || [[Bruker:Trygvis|Trygvis]] ||-||Nei||Nei
|-
| 4 || Variabel strømforsyning || Bitraf || -, [[Oltronix B602D]] ||Nei||Nei
|-
| 1 || [http://the3doodler.com/ 3Doodler] || Jacob N || - ||Nei||Nei
|-
| 1 || [[3D-penn]] (noname) || Erlend || - ||Nei||Nei
|-
| 1 || [[Etse_kort|Utstyr for etsing av kretskort]] || Bitraf || - ||Nei||Nei
|-
| 1 || [[Vinylkutter]] || Bitraf || [[Vinylkutter Cricut Maker 3|Cricut Maker 3]] ||Nei||Nei
|-
| 1 || Cricut vinylkutter || Bitraf || [https://help.cricut.com/hc/en-us/articles/360015214914-Quick-Start-Guide#cricut-maker instruksjoner] || nei || nei
|-
| 1 || [[Wacom tablet]] || Bitraf || [[Wacom tablet]] ||Nei||Nei
|-
| 1 || [[CNC3-3018Pro]] || Bitraf || - ||Ja||Ja
|-
| 1 || [[TDS-3]] || - || [[TDS-3|instruksjoner]] ||Nei||Nei
|-
| 1 || skriver HP LaserJet 100 colorMFP M175nw || Bitraf || [[Utskrift|instruksjoner]] || nei || nei
|-
| 1 || Varmpresse || Bitraf || [[Varmpresse]] || nei || nei
|-
|}
Det er også flere komponentskap med standard-komponenter som motstander, kondensatorer, headere, IC'er m.m. som kan brukes av betalende medlemmer.

== Utstyr i 3D-printer-rommet ==
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! Krever Medlemskap !! Krever Kurs
|-
| 9 || Prusa i3 MK3S (3D printer) || Bitraf || [[3D printing|Instruksjoner]] || nei || nei
|-
| 1 || Elegoo Centauri Carbon 2 Combo (3D printer) || Bitraf || [[Elegoo_Centauri_Carbon_2_Combo_3D_printer|Instruksjoner]] || nei || nei
|-
| 1 || Formlabs Form 3 (Resin Printer) || Bitraf || [[Formlabs_3D_printer|Instruksjoner]] || ja || ja
|-
| 1 || Formlabs Form 1 (Resin Printer) || Bitraf || [[Formlabs_3D_printer|Instruksjoner]] || ja || ja
|-
| 1 || Formlabs Wash || Bitraf || [[Formlabs_3D_printer|Instruksjoner]] || ja || ja
|-
| 1 || Formlabs Cure || Bitraf || [[Formlabs_3D_printer|Instruksjoner]] || ja || ja
|-
| 1 || Monsterkossel Deltaprinter (trenger reperasjon) || Bitraf || [[https://github.com/goeland86/MonsterKossel/ Instruksjoner/github]]] || nei || nei
|-

|}

== Utstyr på PnP-rommet ==
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || [[Pick and place|SmallSMT]]<ref>[https://bitraf.no/wiki/Pick_and_place]</ref> Pick and Place-maskin || [[Bruker:Trygvis|Trygve]]|| [[Pick_and_place|Instruksjoner]]|| Ja||Ja
|-
| 1 || [https://www.eurocircuits.com/ec-equipment-ec-placer/ Manuell Pick'n'place] for små prototype-serier || Bitraf || - ||Nei||Nei
|-
| 1 || [[T-962A|T-962]] Reflow-ovn || Bitraf || -||Nei||Nei
|-
| 1 || [[Ec-reflow-mate|Ec-reflow-mate]] Reflow-ovn || Bitraf || -||Nei||Nei
|-
| 1 || [[Mini-Condens-IT|Mini Condens IT]] dampfase-ovn || Bitraf || [[Mini-Condens-IT|Instruksjoner]] ||Nei?||Nei?
|-
| 1 || Lodde- og reworkstasjon Metcal MX-500 || Kyrre || [[Metcal MX-500|Instruksjoner]] ||Nei||Nei
|-
| 1 || Pinsett-loddestasjon OKI MFR-PS1K || Bitraf || - ||Nei||Nei
|-
| 1 || Varmluft-stasjon Metcal HCT2-120 || No-Isolation || [[Metcal HCT2-120|Instruksjoner]] ||Nei||Nei
|-
| 1 || Reworkstasjon med undervarme Yihua 853AA || Bitraf || [[Yihua853AA|Instruksjoner]] ||Nei||Nei
|-
| 1 || [https://www.ebay.com/itm/313149957097 Elektronisk mikroskop ] m/Autofocus SONY IMX290 sensor || Bitraf ||-||Nei||Nei
|-
| 1 || Optisk mikroskop [https://www.tequipment.net/Vision-Engineering/Mantis-Elite-Universal/ Mantis Elite] (x8 og x15) || Bitraf ||-||Nei||Nei
|-
| 1 || [[Pastamaskin]] || Bitraf || - ||Nei||Nei
|-
| 1 || [[Utstyr for skjøting av SMD-reels]] || Jensa || - ||Nei||Nei
|-
| 1 || Ultralydvasker || Elias || [[Ultralydvasker]] || Nei || Nei
|-
|}

== Utstyr i syrommet ==
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || Pfaff 487-G (industriell symaskin) || Bitraf || [[Symaskiner]] ||Ja||Ja
|-
| 1 || Pfaff Metro Spezial 9346 (skomaker-symaskin) || Bitraf || [[Symaskiner]] ||Ja||Ja
|-
| 1 || Pfaff Hobbylock 2.0 (overlock maskin)|| Darren || [[Symaskiner]] ||Ja||Ja
|-
| 2 || Singer 2250 og 2263 (vanlig symaskin) || - || - ||Ja||Ja
|-
| 1 || Janome Memory Craft 500 E ([[broderimaskin]]) || Bitraf || [[Symaskiner]]|| Ja || Ja
|}

== Utstyr i [[verkstedet]] ==

=== Shopbot CNC ===
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || [[ShopBot]] ([[CNC]] fres) || Bitraf || [[ShopBot|Instruksjoner]]|| Ja ||shopbotkurs
|-
| 1 || kontroller PC || - || - ||Nei||Nei
|-
| 1 || Enkelt utvalg verktøy til Shopbot || - || - ||Nei||Nei
|-
|}

=== General workshop ===
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || [[Nova Voyager søylebormaskin]] || Bitraf || [[Fil:NovaVoyager.pdf]] ||Nei||Nei
|-
| 1 || [[Tormek T8 slipemaskin]] || Bitraf || [https://tormek.com/en/products/sharpening-machines/tormek-t-8-original Informasjon] ||Nei||Ja
|-
| 1 || Dremel multiverktøy || - || - ||Nei||Nei
|-
| 1 || Varmepistol || - || - ||Nei||Nei
|-
| 1 || Limpistoler || - || - ||Nei||Nei
|-
| 1 || Godt utvalg håndverktøy || - || - ||Nei||Nei
|-
| 1 || Batteridriller || - || - ||Nei||Nei
|-
| 1 || Batteri bajonettsager || - || - ||Nei||Nei
|-
| 1 || Batteri bajonettsag || - || - ||Nei||Nei
|-
| 1 || Batteri muttertrekker || - || - ||Nei||Nei
|-
| 1 || Skrustikke || - || - ||Nei||Nei
|-
| 1 || Ambolt || - || - ||Nei||Nei
|-
| 1 || Støvsuger || - || [[Fil:Delfin_DM3_EN_user_manual.pdf]] ||Nei||Nei
|-
|}

=== Snekkerverksted ===
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || Bordsag || - || [[Bordsag|Instruksjoner]] ||Ja||Sikkerhetskurs
|-
| 1 || Slipemaskin || - || - ||Nei||Innføring
|-
| 1 || Kontursag || - || - ||Nei||Nei
|-
| 1 || Dykksag || - || [[Dykksag|Instruksjoner]] ||Ja||Sikkerhetskurs
|-
| 1 || Kapp og Gjæringsag || - || [[Kappsag|Instruksjoner]] ||Nei||Nei
|-
| 1 || Bordfres || - || [[Bordfres|Instruksjoner]] ||Ja||Sikkerhetskurs
|-
| 1 || Håndfres || - || - ||Ja||Innføring
|-
| 1 || Lamellfres || - || - ||Ja||Innføring
|-
| 1 || Båndsag || - || [[Band saw|Instruksjoner]] ||Ja||Sikkerhetskurs
|-
| 1 || Dreiebenk for tre || - || [[WoodLathe|Instruksjoner]] ||Ja||Sikkerhetskurs
|-
|}

=== Kald-metall verksted ===
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || Dreiebenk for [[metallarbeid|metall]] og [[plast]] (ikke tre) || Fredrik Fylling || [[Dreiebenk]]|| Nei||sikkerhetskurs
|-
| 1 || Manuell fres Sieg X3 || Elias || [[Manuell_fres]] ||Nei||Innføring
|-
| 1 || Plateknekke/valse/saks || - || - ||Nei||Innføring
|-
| 1 || Platesaks || - || - ||Nei||Innføring
|-
| 1 || Kaldbåndsag stor|| - || [[Metall_bandsag_stor]] ||Nei||Innføring
|-
| 1 || Kaldbåndsag liten|| - || [[Metall_bandsag]] ||Nei||Innføring
|-
| 1 || Rørbøyer || - || [[Rørbøyer]] ||Nei||Nei
|-
|}

Listen over er ikke komplett, men inneholder det viktigste utstyret. I tillegg har verkstedet et godt utvalg av tenger, skrutrekkere og annet verktøy.

=== Steinarbeid ===

{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || Flisekutter || Bitraf || [[Flisekutter]] || Nei || Nei
|-
|}

== Utstyr i laserrommet ==
Vi har et eget rom for laserkuttere med tilhørende utstyr (kjøling, avtrekk).
{| class="wikitable"
|-
! Antall !! Beskrivelse !! Eier !! Instruksjoner !! krever medlemskap !! Krever Kurs
|-
| 1 || Red Sail Laser 60W (rød)|| Bitraf || [[Laser|Beskrivelse]] || Ja||laserkurs
|-
| 1 || Red Sail Laser 100W (blå)|| Bitraf || [[Laser|Beskrivelse]] || Ja||laserkurs
|-
|}

== Utstyr etter type ==
=== CNC-maskiner ===
{{#ask: [[Category:CNC-maskiner]]
|?Lokasjon
|?Arbeidsområde
|format=table
|mainlabel=Maskin
|class=sortable wikitable smwtable
}}

==Sensornettverk==
[[Sensornettverk]]

== Referanser ==
<references/>

[[Category:Utstyr]][[Category:Elektronikk]]