Bitraf - Brukerbidrag [nb]

Pick and place

2018-06-04T18:56:21Z

Gregers: Air compressor

Bitraf har nå en pick-and-place-maskin (bestykkningsmaskin)
Denne krever kurs, som blir satt opp i løpet av sommeren 2018.

Vi har en SmallSMT [https://www.smallsmt.biz/vp2500hpcl32-pnp-machine VP-2500HP-CL32]

Brukermanualen ligger her: ''Dropbox/Bitraf Felles/Manualer/Vision placer_V2.pdf''

Se for øvrig siden som ble opprettet før vi gikk til innkjøp av maskinen: [[pick_and_place_innkjop]]

== Starting the machine ==
The machine seems picky about the order of start-up. Here is what seems to work <del>consistently</del> best.
# Start VisionPlacer V2,
# Turn the machine on using the shutdown button
# Open the camera
# Press Connect

== Compressed air ==
* Remember to turn on the air compressor in the neighbour room before you begin
* When you're done you should turn off the compressor and release the pressure

== Setting up feeders ==

Det er 3 areas for reel feeders. 19* proprietary component feeders on East, og 23 on West. In addition there is the possibility of 32 CL-feedere in South.

It is possible to position the camerate at the feeders by right-clicking the feeders in the list, and using "Camera to feeder test".

Component rotation happens between picking and visual inspection. So one can check that the component is rotated correctly in the camera view before placement.

* 1 feeder is outside the workarea and cannot be used.

== Using components from tray ==
TODO: document

== Setting up a PCB ==
TODO: document

Physically place the PCB.

In Eleesen SMT Control System:
# PCB button
# Pcb Edit
# "Add" if left column is empty
# Import Pcb File
# Choose file type
## Both Eagle and KiCAD is natively supported, and has been tested.
## In KiCAD, the files must have Windows line endings. If you use Linux, convert the file with an external program.
# Open Pcb File and find file
# Import All To Project
# Ok
# Move camera to PCB origin
# Pcb Edit
# Pcb Properties
## Add PCB height
## Origin X - use the CX to get camera X position
## Origin Y - use the CY to get camera Y position

=== Test coordinate system ===
# Right click a part
# Move camera to part cooridnate
# Verify that the camera moved to the correct position
## If it's not coorect - adjust origin X/Y in Edit Pcb (see above)

== Adjusting origin ==

Testing so far shows that the machine must be adjusted for good results. Do it in this order:

# Visual Origin: Adjust manually with the mouse so the visual origin is in the cross (Set -> Basic Settings -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# PCB Origin: Adjust camera manually to align with the Lower Left corner of the PCB. Click the "PCB Edit" button (fgreen icon). Next to the Origin X & Y, click the CX/CY button to set current position as the coordinate.
# Component Reel origin: Click the Reels-icon and Double-click the reel you want to adjust. Adjust manually with the mouse so the cross is dead centered on the component you want to pick up ( -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# Camera coordinates: Move Nozzle to Camera 1. Adjust so it's dead center. (Set -> Camera List -> Double click Camera 1 -> Set Camera X/Y Coordinates -> Press the X/Y button)

== Known or unknown error messages ==
* 1Feed Error: Wrong feeder has been chosen.
* Error E4: The lid is physically open
* Online Error!: ?
* Mark test error: ?
* Coordinate limit reached ! End: The machine attempts to move outside the work area/ soft limits.

== Part library ==
It is desirable to standardize on a set of components at welldefined positions, for some of the reels.

Possible inspirations include: Seed Studio Open Part Library

https://www.seeedstudio.com/opl.html

[[Category:Elektronikk]]

Pick and place

2018-06-04T18:53:52Z

Gregers:

Bitraf har nå en pick-and-place-maskin (bestykkningsmaskin)
Denne krever kurs, som blir satt opp i løpet av sommeren 2018.

Vi har en SmallSMT [https://www.smallsmt.biz/vp2500hpcl32-pnp-machine VP-2500HP-CL32]

Brukermanualen ligger her: ''Dropbox/Bitraf Felles/Manualer/Vision placer_V2.pdf''

Se for øvrig siden som ble opprettet før vi gikk til innkjøp av maskinen: [[pick_and_place_innkjop]]

== Starting the machine ==
The machine seems picky about the order of start-up. Here is what seems to work <del>consistently</del> best.
# Start VisionPlacer V2,
# Turn the machine on using the shutdown button
# Open the camera
# Press Connect

== Setting up feeders ==

Det er 3 areas for reel feeders. 19* proprietary component feeders on East, og 23 on West. In addition there is the possibility of 32 CL-feedere in South.

It is possible to position the camerate at the feeders by right-clicking the feeders in the list, and using "Camera to feeder test".

Component rotation happens between picking and visual inspection. So one can check that the component is rotated correctly in the camera view before placement.

* 1 feeder is outside the workarea and cannot be used.

== Using components from tray ==
TODO: document

== Setting up a PCB ==
TODO: document

Physically place the PCB.

In Eleesen SMT Control System:
# PCB button
# Pcb Edit
# "Add" if left column is empty
# Import Pcb File
# Choose file type
## Both Eagle and KiCAD is natively supported, and has been tested.
## In KiCAD, the files must have Windows line endings. If you use Linux, convert the file with an external program.
# Open Pcb File and find file
# Import All To Project
# Ok
# Move camera to PCB origin
# Pcb Edit
# Pcb Properties
## Add PCB height
## Origin X - use the CX to get camera X position
## Origin Y - use the CY to get camera Y position

=== Test coordinate system ===
# Right click a part
# Move camera to part cooridnate
# Verify that the camera moved to the correct position
## If it's not coorect - adjust origin X/Y in Edit Pcb (see above)

== Adjusting origin ==

Testing so far shows that the machine must be adjusted for good results. Do it in this order:

# Visual Origin: Adjust manually with the mouse so the visual origin is in the cross (Set -> Basic Settings -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# PCB Origin: Adjust camera manually to align with the Lower Left corner of the PCB. Click the "PCB Edit" button (fgreen icon). Next to the Origin X & Y, click the CX/CY button to set current position as the coordinate.
# Component Reel origin: Click the Reels-icon and Double-click the reel you want to adjust. Adjust manually with the mouse so the cross is dead centered on the component you want to pick up ( -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# Camera coordinates: Move Nozzle to Camera 1. Adjust so it's dead center. (Set -> Camera List -> Double click Camera 1 -> Set Camera X/Y Coordinates -> Press the X/Y button)

== Known or unknown error messages ==
* 1Feed Error: Wrong feeder has been chosen.
* Error E4: The lid is physically open
* Online Error!: ?
* Mark test error: ?
* Coordinate limit reached ! End: The machine attempts to move outside the work area/ soft limits.

== Part library ==
It is desirable to standardize on a set of components at welldefined positions, for some of the reels.

Possible inspirations include: Seed Studio Open Part Library

https://www.seeedstudio.com/opl.html

[[Category:Elektronikk]]

Pick and place

2018-06-04T18:47:28Z

Gregers: Added a note where the user manual is located

Bitraf har nå en pick-and-place-maskin (bestykkningsmaskin)
Denne krever kurs, som blir satt opp i løpet av sommeren 2018.

Vi har en SmallSMT [https://www.smallsmt.biz/vp2500hpcl32-pnp-machine VP-2500HP-CL32]

Brukermanualen ligger her: ''Dropbox/Bitraf Felles/Manualer/Vision placer_V2.pdf''

Se for øvrig siden som ble opprettet før vi gikk til innkjøp av maskinen: [[pick_and_place_innkjop]]

== Starting the machine ==
The machine seems picky about the order of start-up. Her eis what seems to work consistently.
# Start VisionPlacer V2,
# Turn the machine on using the shutdown button
# Open the camera
# Press Connect

== Setting up feeders ==

Det er 3 areas for reel feeders. 19* proprietary component feeders on East, og 23 on West. In addition there is the possibility of 32 CL-feedere in South.

It is possible to position the camerate at the feeders by right-clicking the feeders in the list, and using "Camera to feeder test".

Component rotation happens between picking and visual inspection. So one can check that the component is rotated correctly in the camera view before placement.

* 1 feeder is outside the workarea and cannot be used.

== Using components from tray ==
TODO: document

== Setting up a PCB ==
TODO: document

Physically place the PCB.

In Eleesen SMT Control System:
# PCB button
# Pcb Edit
# "Add" if left column is empty
# Import Pcb File
# Choose file type
## Both Eagle and KiCAD is natively supported, and has been tested.
## In KiCAD, the files must have Windows line endings. If you use Linux, convert the file with an external program.
# Open Pcb File and find file
# Import All To Project
# Ok
# Move camera to PCB origin
# Pcb Edit
# Pcb Properties
## Add PCB height
## Origin X - use the CX to get camera X position
## Origin Y - use the CY to get camera Y position

=== Test coordinate system ===
# Right click a part
# Move camera to part cooridnate
# Verify that the camera moved to the correct position
## If it's not coorect - adjust origin X/Y in Edit Pcb (see above)

== Adjusting origin ==

Testing so far shows that the machine must be adjusted for good results. Do it in this order:

# Visual Origin: Adjust manually with the mouse so the visual origin is in the cross (Set -> Basic Settings -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# PCB Origin: Adjust camera manually to align with the Lower Left corner of the PCB. Click the "PCB Edit" button (fgreen icon). Next to the Origin X & Y, click the CX/CY button to set current position as the coordinate.
# Component Reel origin: Click the Reels-icon and Double-click the reel you want to adjust. Adjust manually with the mouse so the cross is dead centered on the component you want to pick up ( -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# Camera coordinates: Move Nozzle to Camera 1. Adjust so it's dead center. (Set -> Camera List -> Double click Camera 1 -> Set Camera X/Y Coordinates -> Press the X/Y button)

== Known or unknown error messages ==
* 1Feed Error: Wrong feeder has been chosen.
* Error E4: The lid is physically open
* Online Error!: ?
* Mark test error: ?
* Coordinate limit reached ! End: The machine attempts to move outside the work area/ soft limits.

== Part library ==
It is desirable to standardize on a set of components at welldefined positions, for some of the reels.

Possible inspirations include: Seed Studio Open Part Library

https://www.seeedstudio.com/opl.html

[[Category:Elektronikk]]

Pick and place

2018-06-04T18:35:59Z

Gregers: Basics for adding a new PCB design

Bitraf har nå en pick-and-place-maskin (bestykkningsmaskin)
Denne krever kurs, som blir satt opp i løpet av sommeren 2018.

Vi har en SmallSMT [https://www.smallsmt.biz/vp2500hpcl32-pnp-machine VP-2500HP-CL32]

Se for øvrig siden som ble opprettet før vi gikk til innkjøp av maskinen: [[pick_and_place_innkjop]]

== Starting the machine ==
The machine seems picky about the order of start-up. Her eis what seems to work consistently.
# Start VisionPlacer V2,
# Turn the machine on using the shutdown button
# Open the camera
# Press Connect

== Setting up feeders ==

Det er 3 areas for reel feeders. 19* proprietary component feeders on East, og 23 on West. In addition there is the possibility of 32 CL-feedere in South.

It is possible to position the camerate at the feeders by right-clicking the feeders in the list, and using "Camera to feeder test".

Component rotation happens between picking and visual inspection. So one can check that the component is rotated correctly in the camera view before placement.

* 1 feeder is outside the workarea and cannot be used.

== Using components from tray ==
TODO: document

== Setting up a PCB ==
TODO: document

Physically place the PCB.

In Eleesen SMT Control System:
# PCB button
# Pcb Edit
# "Add" if left column is empty
# Import Pcb File
# Choose file type
## Both Eagle and KiCAD is natively supported, and has been tested.
## In KiCAD, the files must have Windows line endings. If you use Linux, convert the file with an external program.
# Open Pcb File and find file
# Import All To Project
# Ok
# Move camera to PCB origin
# Pcb Edit
# Pcb Properties
## Add PCB height
## Origin X - use the CX to get camera X position
## Origin Y - use the CY to get camera Y position

=== Test coordinate system ===
# Right click a part
# Move camera to part cooridnate
# Verify that the camera moved to the correct position
## If it's not coorect - adjust origin X/Y in Edit Pcb (see above)

== Adjusting origin ==

Testing so far shows that the machine must be adjusted for good results. Do it in this order:

# Visual Origin: Adjust manually with the mouse so the visual origin is in the cross (Set -> Basic Settings -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# PCB Origin: Adjust camera manually to align with the Lower Left corner of the PCB. Click the "PCB Edit" button (fgreen icon). Next to the Origin X & Y, click the CX/CY button to set current position as the coordinate.
# Component Reel origin: Click the Reels-icon and Double-click the reel you want to adjust. Adjust manually with the mouse so the cross is dead centered on the component you want to pick up ( -> Visual Origin Coordinate -> Click the CX & CY buttons to set current position as origin)
# Camera coordinates: Move Nozzle to Camera 1. Adjust so it's dead center. (Set -> Camera List -> Double click Camera 1 -> Set Camera X/Y Coordinates -> Press the X/Y button)

== Known or unknown error messages ==
* 1Feed Error: Wrong feeder has been chosen.
* Error E4: The lid is physically open
* Online Error!: ?
* Mark test error: ?
* Coordinate limit reached ! End: The machine attempts to move outside the work area/ soft limits.

== Part library ==
It is desirable to standardize on a set of components at welldefined positions, for some of the reels.

Possible inspirations include: Seed Studio Open Part Library

https://www.seeedstudio.com/opl.html

[[Category:Elektronikk]]